Anaesth-Assist NXT (2 Gas Model)

Standard Specification:

• Non Metallic water resistant and fire retardant moulded body made from engineering grade polymer.

• Back-lit illuminated 2 gas, cascaded 4 tube Rotameter.

• Selecta tech bar for one temperature and pressure  compensated agent specific vaporiser.

• Diameter coded self sealing type inlet for piped gas (1 each for O2 and N2O) with non return.

• Pin indexed type yoke for bottled oxygen and Nitrous Oxide(1 each).

• Master switch for system ON/OFF for gases and powersupply.

• Common gas outlet.

• Open/close circuit switch for easy change over from open to close circuit.

• Integrated Power backup and extra electrical extension outlets for running other devices.

• Integrated microprocessor based pneumatically driven ventilator.

• Interactive test for confirming proper device operation during start-up.

• Circle absorber system with integrated ventilator bellow, bag ventilator selector switch with active changeover.

• Anesthetic gas scavenging system port in Circle Absorber.

• Resistant to external Electro Magnetic Interference (Both Ambient and Conductive).

Note:** Images shown here are for illustrave purpose only**
Ventilator Specifications:

• Ventilation parameters automatically calculated and set by patient BMI.

• Patient Groups: Neonate, Paediatric and Adult.

• Ventilation Mode : CMV(V), CMV(P), SIMV(V), SIMV(P) and Manual(Bag).

• Digital and compensated Tidal Volume control in ventilator.

• Tidal Volume adjustment: 20 ~ 1500mL.

• I:E ratio: 4:1 to 1:4.

• Frequency Adjustment range: 1 ~ 60 b.p.m. (in different modes).

• Monitoring: Vti, VTe, MV, FIO2, PEEP, Ppeak, Cdyn and Timer.

• On the go changing of VT, Ppeak, BPM, I:E Ratio, PEEP and Itrig.

• 7” Full Colour Touch Screen Display.

• Inbuilt FiO2 monitor with adjustable high and low alarm with FiO2 sensor calibration feature.

• Flow sensor calibration data input feature.

• Waveform: Flow vs Time and Pressure vs Time(also                 available during Manual Bag Ventilation).

• Ventilatory loops: Volume vs Pressure and Flow vs Volume.

• Alarm for High and Low AWP, MV, FiO2, Timer, Low oxygen pressure and critical battery status.

• Electronic PEEP control from 0 ~ 20cm of water column.

• Pressure Trigger: -3~+19cm of water column(SIMV Mode).

• Pressure Limit: Patient airway 5~65 cm of water column.

• Airway pressure monitoring range -3~100 cm of water.

• Accurate display of Inspiratory and expiratory volume using proximal flow sensor.

• Fresh gas flow compensation in all mode of ventilation.

• Animated inspiratory and expiratory phase graphic during CMV/SIMV.

• Audible alarm volume control.

• Reminder of audio alarm mute at every 120 seconds during alarm condition.

• Reminder of device running on battery backup after every 33 seconds.

• Ventilator set parameter data automatically saved and stored by the ventilator.

• Data recording of the patient and set values and alarms for the last 72 hours of use.

• Programmable anaesthesia drug timer with alarm.

Patient Safety:

• Tested for IEC 60601-1:2005 + AMD1:2012+ AMD2: 2020 from NABL accredited and CDSCO approved Lab.

• Gear linked mechanical Hypoxic control device

• Fresh gas compensation during inspiratory saving from Volutrauma.

• Nitrous oxide interlocking

• Emergency Oxygen flush

• FiO2 display (while using close circuit)

• Breathing system pressure relief valve set at 1200mm of water column.

• Audio visual oxygen pressure alarm.

• Audio visual critical battery alarm.

• Low and high airway pressure alarm.

• Low and high minute volume alarm.

• Low and high FiO2 alarm.

• Waveform monitor during manual bag ventilation.